Tankless Water Heaters - The Good and the Bad

Info - Tankless water heaters information

Tankless Hot Water Heaters

Get paid on 100% of your website traffic, no clicks necessary!

Tankless water heaters....the GOOD...and the BAD!

Tankless heaters have pros and cons, just like everything else. They can supply an endless supply of hot water, and can save energy.

However, they are limited in the amount of hot water that can be produced at one time and they are more expensive to purchase than a conventional storage type water heater.

They also make it take longer for you to get your hot water, since they don't start heating the water until you turn on the faucet. This problem can be solved by using a specialized pump, which in combination with the tankless unit can get your hot water to you at less than half the time it would take running the faucet full blast.

The tankless water heaters also cause an increase in water wastage since you have to let the water run longer to get your hot water. This problem is also solved when using the specialized pumping system. Water conservation is an important advantage to the pumping system. One such system is the Chilipepper hot water pump. With it you get both water conservation and convenience benefits of faster hot water, and, an un-limited amount of hot water.

Tankless hot water heaters save energy and thus money. Water heating accounts for 20% or more of an average household’s annual energy expenditures. The yearly operating costs for conventional gas or electric storage tank water heaters average $200 or $450, respectively.

Storage tank-type water heaters raise and maintain the water temperature to the temperature setting on the tank (usually between 120° -140° F (49° -60° C). Even if no hot water is drawn from the tank (and cold water enters the tank), the heater will operate periodically to maintain the water temperature.

This is due to "standby losses": the heat conducted and radiated from the walls of the tank—and in gas-fired water heaters—through the flue pipe. These standby losses represent 10% to 20% of a household’s annual water heating costs.

Tankless units are common in Japan and Europe. They began appearing in the United States about 30 years ago. Unlike "conventional" storage tank water heaters, tankless water heaters heat water only as it is used, or on demand. A tankless hot water heater has a heating device that is activated by the flow of water when a hot water valve is opened. Once activated, the heater delivers a constant supply of hot water. The output, however, limits the rate of the heated water flow.

Selecting a Tankless Water Heater

Select a based on the maximum amount of hot water to meet your peak demand. Use the following assumptions on water flow for various appliances to find the size of unit that is right for your purposes:

Faucets: 0.75 gallons (2.84 liters) to 2.5 gallons (9.46 liters) per minute.

Low-flow showerheads: 1.2 gallons (4.54 liters) to 2 gallons (7.57 liters) per minute.

Older standard shower heads: 2.5 gallons (9.46 liters) to 3.5 gallons (13.25 liters) per minute.

Clothes washers and dishwashers: 1 gallon (3.79 liters) to 2 gallons (7.57 liters) per minute.

Unless you know otherwise, assume that the incoming potable water temperature is 50° F (10° C). You will want your water heated to 120° F (49° C) for most uses, or 140° F (60° C) for dishwashers without internal heaters. To determine how much of a temperature rise your need, subtract the incoming water temperature from the desired output temperature. In this example, the needed rise is 70° F (39° C).

List the number of hot water devices you expect to have open at any one time, and add up their flow rates. This is the desired flow rate for the water heater. Select a manufacturer that makes such a unit. Most tankless hot water heaters are rated for a variety of inlet water temperatures. Choose the model that is closest to your needs.

As an example, assume the following conditions: One hot water faucet open with a flow rate of 0.75 gallons (2.84 liters) per minute. One person bathing using a shower head with a flow rate of 2.5 gallons (9.46 liters) per minute. Add the two flow rates together. If the inlet water temperature is 50° F (10° C), the needed flow rate through the heater would need to be no greater than 3.25 gallons (12.3 liters) per minute. Faster flow rates or cooler inlet temperatures will reduce the water temperature at the most distant faucet. Using low-flow showerheads and water-conserving faucets are a good idea.

Some types are thermostatically controlled. They can vary their output temperature according to the water flow rate and the inlet water temperature. This is useful when using a solar water heater for preheating the inlet water. If, using the above example, you connect this same tankless water heater to the outlet of a solar system, it only has to raise the water temperature a few degrees more, if at all, depending on the amount of solar gain that day.

Gas and electric models.

Tankless Water Heater Enjoy endless showers, save space, energy, money.

Chilipepper Sales 10 Greg St., # 110 Sparks Nevada, 89431 1-800 914-9887

Inventors Trivia Lovers links 2 links 3 links 4